收藏本站
13
6.3
Communication
When communication of either text or commands is interrupted, try the steps below.
?
First, check the communication cable for continuity. If you don't have an ohm meter, try using a
different communication cable. If you are using a PC try using a different Com/USB Port.
?
Next, please ensure that the display module is set to communicate on the protocol that you are
using, by checking the Protocol Select Jumpers.
?
In serial and USB protocols, ensure that the host system and display module are both
communicating on the same baud rate.
The default rate for the display module is 19200 bps.
?
Match Rx from your display to the transmitting pin from your host and the Tx pin to the
receiving pin.
?
If you are communicating to the display via I2C*
please ensure that the data is being sent to the
correct address. The default slave address for the display module is 80.
?
In I2C mode, connect Rx to the clock line of your controller and Tx to the data output.
?
Unlock the display. See the Set and Save Data Lock command for more info.
?
Finally, you may reset the display to its default settings using the Manual Override
procedure
outlined below.
*Note:
I2C communication will always require pull up resistors on SCL and SDA of one to ten kilohms.
6.4
Manual Override
Should the settings of your display become altered in a way that dramatically impacts usability, the
default settings can be temporarily restored. To override the display, please follow the steps below.
1.
Disconnect power from your display.
2.
Place a jumperon the GPIOpins
labelled3 and 4.
3.
Reconnect power to your unit, and wait for the start screen before removing the jumper.
4.
Settings will be temporarily**
overridden to the defaults listed in the Manual Override Settings
table. At this point any important settings, such as contrast, backlight, or baud rate, should not only
be set but saved so they remain when the override is removed.
Parameter
Value
Backlight
255
Contrast
128
Baud Rate
19200
I2C Address
80
Table 10: Manual Override Settings
**Note:
The display module will revert back to the old settings once turned off,
unless desired settings are saved.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
VK202-25-USB-E VF CHARACTER DISPLAY 20X2 USB
VK202-25-VPT VFD ALPHA/NUM DISPLAY 20X2
VK204-25-422 VF CHARACTER DISPLAY 20X4 RS422
VK204-25-VPT VFD ALPHA/NUM DISPLAY 20X4
VLM-532-42-SCA LASER MODULE 532NM 1-5MW DOT
VLM-532-46-LCA LASER MODULE 532NM 1-5MW LINE
VLM-635-14-SPA LASER MODULE 635NM 1-5MW DOT
VLM-635-15-LPA LASER MODULE 635NM 1-5MW DOT
相关代理商/技术参数
VK-170613 制造商:Messing Gegenmutter 功能描述:
VK-171502 制造商:Messing Gegenmutter 功能描述:
VK1AS001-MZZ00-000 制造商:Carling Technologies 功能描述:V-SERIES ROCKER SWITCH - Bulk
VK2/AO-1B 制造商:IMO Precision Controls Ltd 功能描述:PROXIMITY SWITCH M18 AC
VK2/AO-1B 制造商:IMO Precision Controls Ltd 功能描述:PROXIMITY SWITCH M18 AC
VK-20 制造商:Wieland Electric Inc 功能描述:ELECTRICAL, DUCT/RACEWAY (TRUNKING) 制造商:Wieland Electric Inc 功能描述:ELECTRICAL, DUCT/RACEWAY (TRUNKING); Raceway / Duct Color:Grey; External Height:21mm; Raceway / Duct Material:Polyamide; Series:Flexible Slot; External Width:23mm; Accessory Type:Wiring Duct; Body Material:Polyamide; Color:Gray ;RoHS Compliant: NA
VK200 10/3B 制造商:AMPERX 功能描述:
VK20009-3S WBC1.5/A-3S4 制造商:F-CUBE 功能描述: